Skip to main content
AudioCodes Device Provisioning
8x8 Support Knowledge Base

AudioCodes Device Provisioning

Overview

Use this information to provision an AudioCodes ATA adapter or to recover it after a factory reset.

Firmware version for AudioCodes MP112, MP114, MP118, MP124E: 6.60A.332.002

Firmware version for AudioCodes MP124: 6.60A.323.005

To restore the AudioCodes ATA to factory default

  1. Remove the LAN Cable.
  2. Hold the reset button for 10 seconds.
  3. Wait for the Ready Status to be Green.
  4. Reconnect the LAN cable.

To make the AudioCodes ATA reach the IVR

  1. Dial ***12345 to access IVR.
  2. Dial 1 # to get the IP address.
  3. Enable the DHCP.
    1. Dial ***12345.
    2. Input 7 # to enter DHCP Menu.
    3. Input # to change.
    4. Input 1 # to enable.
    5. Input 1 to save.
    6. Reconnect the LAN cable.
    7. Dial ***12345 to access IVR.
    8. Dial 1 # to get the IP address.
  4. In browser navigate to https://<IPADDRESS from IVR>.
    • Username: Admin
    • Password: Admin
      AudioCodeLogin.png
  5. Check the firmware version by going to Status & Diagnostics > System Status > Device Information > Versions > Version ID.
  6. If the firmware is up to date, skip to the next section to load the bootstrap INI file.
  7. Go to Device Actions.
  8. Save the configuration file.
    DeviceActions.png
  9. Create one empty ini file which will be used to wipe out the configuration.
  10. Go to Software Wizard.
    AudioCodesLoadingFirmware2_0.png
  11. Load the latest firmware.
    AudioCodesLoadingFirmware3_0.png
    AudioCodesLoadingFirmware4_0.png
    AudioCodesLoadingFirmware6_0.png
  12. Load the empty ini file.
    AudioCodesLoadingFirmware7_0.png
  13. Click Reset.
    AudioCodesLoadingFirmware8_0.png
    AudioCodesLoadingFirmware9_0.png
  14. After rebooting, open Wireshark Listen on all interfaces and type syslog to monitor logs.
  15. Go to https://<IPADDRESS from IVR>.
  16. Check the firmware version.

Load the Bootstrap INI File

  1. Go to Device Actions.
    AudioCodesLoadingConfig_0.png
  2. Click Load Configuration File.
    AudioCodesLoadingConfig2_0.png
  3. Click Choose File and select the bootstrap ini file.
    AudioCodesLoadingConfig3_1.png
  4. Click Load INI File.
    AudioCodesLoadingConfig4_0.png
  5. A message will appear. Click OK.
    AudioCodes_after-upload-bootstrap-file.png
  6. Wait for the device to reboot. The screen will display, "Loading in Progress...," and then you should be taken back to the login screen.
  7. If the screen is stuck at "Loading in Progress" for over five minutes, refresh the page and you should be taken back to the login screen.
  8. To verify if the Line or Port is registered, go to Status & Diagnostics > VoIP Status > Registration Status.
    Registration_Status2.png

Workaround when IVR does not work

  1. Factory Reset the device.
    1. Remove the LAN Cable.
    2. Hold the reset button for 10 seconds.
    3. Wait for the Ready Status to be Green.
    4. Re-plug the LAN cable.
  2. Plug the ethernet cable to the device and your laptop.
  3. Make your IP address of LAN static to 10.1.10.20.
  4. Access the ATA device on 10.1.10.10.
  5. Load the bootstrap ini file with the steps stated above.
  6. Unplug the ethernet cable from the laptop and connect it to POE.
  7. Wait for the device to reboot. Note: Never reboot a device if some of the lights are RED!
  8. If needed, manually reboot the device.

 

  • Was this article helpful?